关键字:
 
 
水冷式工业冷水机
风冷式工业冷水机
水冷螺杆式冷水机
风冷螺杆式冷水机
工业冷油机
工业冷风机
激光冷水机
电镀冷水机
低温冷冻机
PCB专用冷水机
冷热两用控温机
工业冷水机(定制机)
模温机
苏州奥天诚机械有限公司
15298866904
0512-55198536-816
 
 

冷水机的操作说明


点击次数:2110 来源网站:深圳市奥诚机械有限公司 发布时间:2015-06-25

1、开机顺序:Startup:

(1).开启冷却水塔及循环水泵。

Start the cooling water tower and circulating pump.

(2).开启本机电源,无熔丝开关(NFB控制箱内)。

Start machine’s power supply and no-fuse breaker (inside the NFB controlling box).

(3).开启控制板面运行→压缩机1→压缩机2(如单压缩机不开)→设定所需之温度。

Start the controlling panel, runCompressor 1Compressor 2 (off when single compressor in use)set up the temperature.

(4).按本机电源后,可能产生以下情况:泵浦反转指示灯亮,蜂鸣器警告。关闭电源,将外部三相电源线中之任意两项以对换位置,接回即可。

It may occur that pump reversal indicator light is on and the buzzer alarms when you turn on the machine. Turn it off and change the locations of any two of the three-phase source wires, connect again.

(5).按运行键,可能产生以下情况:泵浦过载指示灯亮,蜂鸣器警告。请压下马达积热电驿之复归按钮,并检查三相电源是否欠相。

It may occur that pump overload indicator light is on and the buzzer alarms when you press ‘run’ key. Please press the reset button of motor thermalrelay, and check if three-phase sources are phase deficient.

(6).如有警报产生(蜂鸣器叫)时,按停止健 再按复归键,则蜂鸣器不叫但灯会亮,等故障排除后灯才会熄灭。

When there is alarm (the buzzer is on), press the stop key and then reset key, so the buzzer will be silent but the light will be on until the problem is solved. 

2、关机顺序:依开机顺序,反顺序关机即可。

Turnoff: Opposite to the sequence of startup.

3、运转情况:

(1).冷媒低压表3.5 Kg /cm2-4.5 Kg /cm2 (54psI-64psI)

(2).冷媒高压表勿高于20 Kg /cm2

Operating Conditions:

(1).Cooling medium low pressure: 3.5 Kg /cm2-4.5 Kg /cm2 (54psI-64psI)

(2).Cooling medium high pressure: less than 20 Kg /cm2

 

 

江苏冷水机_昆山冷水机_天津冷水机_电镀冷水机_苏州螺杆式冷水机_苏州压铸模温机-苏州奥天诚机械有限公司

          联系人:蒋先生 15298866904 电 话:0512-55198536-816  传  真:0512-50393586   地址:苏州昆山市玉山镇五联路228号   邮 编:215300                                                                                                                                        

苏ICP备11070999号-3